How To Install Viper Keyless Entry System

Posted on
Where To Buy

How To Install A Car Alarm, Remote Start, Or Keyless Entry System Read How To Install A Car Alarm, Remote Start, Or Keyless Entry System Review. Aug 17, 2010 - Unfortunately, I was not able to get it installed, because my driver side lock mechanism is sticking. I've been fighting that for a while and decided that it would be a waste to start installing a keyless entry system on a power door lock that doesn't work. Between that and the cold, I've put it on hold. How To Install A Car Alarm, Remote Start, Or Keyless Entry System Read How To Install A Car Alarm, Remote Start, Or Keyless Entry System Review. Viper Car Alarms, Remote Car Starters and Keyless Entry Systems 2014 Models. Featuring: Viper, Hornet, Avital, Clifford Parts, Xpresskit, Autostart, Orion Cobalt, Your Valet, Python, Spal and Alarm Parts.

My first DIY video! So i bought this system because 1.

My key remote did not come with the car 2. Its cheap $50, 3. Its supposed to be easy to install. So far so good. The hard part was actually trusting bulldog's tech support and site as their bmw e36 wiring diagrams are different than mine.

The instruction manual also called to hook up the red wire, when in fact, you need the red and purple wires together on the +12v. Lots of techno babble so i kept it simple. It works and its easy. I hope people learn from this and my future vids:).

So dont be scared to take on simple jobs like this!

Digital Decor Digital Trio Viewer Manual Lymphatic Drainage. • M M o o d d e e l l 2 2 1 1 1 1 H H V V I I n n s s t t a a l l l l a a t t i i o o n n G G u u i i d d e e NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional. • Code Hopping, Doubleguard, ESP, FailSafe, Ghost Switch, Learn Routine™, Nite-Lite ® ® ® ® ® ® Nuisance Prevention Circuitry, NPC, Revenger, Silent Mode™, Soft Chirp, Stinger®, Valet ® ® ® ® ® Vehicle Recovery System, VRS, and Warn Away.

• Table of Contents p p r r i i m m a a r r y y h h a a r r n n e e s s s s ( ( H H 1 1 ) ),, 1 1 2 2 - - p p i i n n c c o o n n n n e e c c t t o o r r..4 4 P P e e r r i i p p h h e e r r a a l l P P l l u u g g - - I I n n H H a a r r n n e e s s s s e e s s. • primary harness (H1), 12-pin connector (+) 12V CONSTANT POWER INPUT H1/1 BLUE (-) 200 mA SECOND UNLOCK OUTPUT H1/2 BLACK/WHITE-1 INPUT OF DOMELIGHT SUPERVISION RELAY #87 H1/3 BLACK/WHITE OUTPUT OF DOMELIGHT SUPERVISION RELAY #30 H1/4 GREEN/BLACK LOCK #30 COMMON OUTPUT H1/5 WHITE/BLACK LOCK #87 NORMALLY CLOSED. • H1/3 BLACK/WHITE-1 Domelight Supervision Input This wire determines what the output polarity of H1/4 will be. If the door pin circuit is negative, connect to chassis ground. If the door circuit is positive, connect to a fused 12V source. The H1/3 wire is not required for wiring the door locks. Depending on the type of door lock system, there may be additional wires for the Door Lock wiring that are not required.

• H1/11 BLACK (-) Chassis Ground Connection Connect this wire to a clean, paint-free sheet metal location (driver kick panel) using a factory bolt that DOES NOT have any vehicle component grounds attached to it. A screw should only be used when in conjunction with a two-sided lock washer. • H1/15 YELLOW (+) Switched Ignition Input Connect this wire to an ignition source. This input must show (+)12V with the key in run position and during cranking. Make sure that this wire cannot be shorted to the chassis at any point. This wire will trigger the system if the ignition is turned on before the unit is disarmed (doors unlocked with the remote). Never use this wire to drive anything but a relay or a low-current input!

The transistorized output can only supply 200 mA of current. Connecting directly to a solenoid, motor, or other high-current device will cause it to fail. Peripheral Plug-In Harnesses Super Bright LED, 2-Pin WHITE Plug The super bright LED operates at (+) 2 volt DC and plugs into the two-pin WHITE port.

• Valet/Program Switch, 2-Pin BLUE Plug The Valet/Program button should be accessible from the driver’s seat. It plugs into the BLUE port on the side of the unit. Consider how the button will be used before choosing a mounting location. Check for rear clearance before drilling a 9/32-inch hole and mounting the button. System Features Learn Routine The System Features Learn Routine dictates how the unit operates. The Valet /Program switch can now be released. ® For example, to program the arming mode from active to passive, within 10 seconds of turning the ignition off, and press and release the Valet/Program switch once.